Quantum P1000 Guía de usuario Pagina 117
- Pagina / 132
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix B Installing the Slide Assembly in the Rack
Installing the Slide Assembly in the Rack
ATL P1000 Series User’s Guide 101
Installing the Slide Assembly in the
Rack
B
To install the slide assembly in the rack (see figure 55 on page 102):
Procedure
1
Loosen (but do not remove) the nuts holding the rear mounting
brackets to the slide assembly.
2
Measure the depth of the rack, from the outside edge of the front
retma rail to the outside edge of the rear retma rail.
3
Adjust the rear mounting brackets so that the distance from the
front mounting brackets to the rear mounting brackets is slightly
greater than the depth of the rack.
4
Insert the slide assembly into the rack:
a
Lift the slide assembly and tilt it sideways.
b
Insert the back end of the slide assembly into the front of the
rack, keeping the slide assembly above the temporary support
screws.
c
When the rear brackets clear the rear retma rails, turn the slide
assembly right side up.
d
Place the slide assembly in the rack so that each bracket rests
on a temporary support screw.
5
Secure the front mounting brackets to the front retma rails, using
four screws from the accessories kit.
6
Adjust the rear mounting brackets so they are flush with the
outside of the rear retma rails.
7
Secure the rear mounting brackets to the rear retma rails, using
four screws from the accessories kit.
Note:
Do not tighten the nuts securing the rear mounting brackets to
the slide assembly. You will tighten these during the following
procedure, “Adjusting the Slide Assembly.”
8
Remove the four temporary support screws.
- User’s Guide 1
- Audience 13
- Document 13
- Organization 13
- Table 1 Related 14
- Documentation 14
- Library Description 17
- Chapter 1 Library Description 18
- Figure 2 P1000 Front 18
- View, Rack-mount Library 18
- Configuration Options 19
- Figure 3 P1000 Library 20
- Back View 20
- Library Elements 21
- Figure 4 Library Elements 22
- Robotics Operation 23
- Front Panel 24
- PRODUCTS 25
- Load Port 26
- Load and Bulk Packs 26
- Back Panel 27
- Tape Drives 28
- Installing the P1000 Library 29
- Site Requirements 30
- Floor Clearance 31
- Floor Strength and 31
- Inclination 31
- Overhead Clearance 31
- Power and Grounding 31
- Figure 11 AC Power 32
- Receptacle 32
- Unpacking the P1000 33
- Uncrating the Library 34
- Checking the 36
- Contents 36
- Preparing and Inserting Tape 46
- Cartridges 46
- Orange tab 48
- Write-protect switch 48
- Placing Tape 50
- Cartridges in the Load 50
- Connecting Host Computers 51
- Figure 26 Single-Host 52
- SCSI Configuration 52
- Figure 28 Five-Host SCSI 54
- Configuration 54
- Turning On the Library 55
- Table 3 Sample Library 56
- Basic Operations 57
- Chapter 3 Basic Operations 59
- Using the GUI 59
- Table 4 Vertical Bar 59
- Buttons and Indicators 59
- Table 6 GUI Screens 61
- Figure 31 GUI Screens 61
- Obtaining Library Status 62
- Activity 63
- Load Pack 64
- Tapes Screen 64
- Performing Manual Operations 67
- Opening the Library 70
- Manually Ejecting a 71
- Cartridge 71
- Operator Commands 73
- Configure 76
- Configuring Library Options 78
- Performing an Inventory 82
- Calibrating the Library 83
- Chapter 4 Operator Commands 84
- Exercising the Library 85
- Unloading the Load Port 87
- Service Commands 89
- Performing a Service 96
- Calibration 96
- Chapter 5 Service Commands 97
- Reenter the new password 100
- Press the Execute button 100
- Troubleshooting 101
- Start-up Problems 102
- GUI Problems 103
- Robotics Problems 104
- Operating Problems 106
- Tape Drive Problems 108
- Specifications 109
- Appendix A Specifications 110
- Table 16 Environmental 110
- Rack Current Rating 114
- Consideration 114
- Grounding 114
- Temperature 114
- Procedure 115
- Procedure (continued) 116
- Figure 55 Installing the 118
- Slide Assembly in the Rack 118
- Adjusting the Slide Assembly 119
- Adjusting the Slide 121
- Assembly Tray on the 121
- Slide Rails 121
- Glossary 125
Relacionado con productos y manuales para Cargadores automáticos de cinta y bibliotecas Quantum P1000
(259 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales