Quantum Scalar 1000 Guía de usuario Pagina 43
- Pagina / 122
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
ADIC Management Console User’s Guide 35
When a device is selected, the lower part of the data panel display presents the following information:
Status/Message Area
The area at the very bottom of the screen is used to display status messages. It is called the
Status/Message Area.
Address Identifier Arbitrated Loop_Physical Address (AL_PA) Address
Host Type OS of attached Host
Loop ID 0-125
Frame Size 512, 1024, or 2048
Frame Buffer Size Storage space, usually bigger than a single frame
Connection Connection options for FC chips
Max Speed 1 GB or 2 GB
Status Ready or Not Ready
Link Error Statistics Header: Subsequent numbers are errors counted by
SNC on full duplex channel between two network fabric
connections
Link Failure Count Counts used in diagnostics
Loss of Sync Count Counts used in diagnostics
Loss of Signal Count Counts used in diagnostics
Primitive Sequence Protocol Error
Count
Transmission word containing special control
information. A primitive sequence is recognized when
three transmission words of the same value are
received
Invalid Transmission Word Count Transmission word is 40 bits, smallest information unit
transmitted
Invalid CRC Count Cyclic Redundancy Check, an error detection algorithm
Vendor ID Vendor Name
Product ID Product Name, assigned by Vendor
Revision Vendor’s release number
Serial Number Number assigned to the device during manufacturing
Removable Yes or No
Capacity For Disk devices, Number of Blocks
Block Size For Disk devices, Size of block
Width For Tape devices, Bus width in bits
Speed For Tape devices, Bus speed
- User’s Guide 1
- 89558 Böhmenkirch 2
- Contents 3
- 6 Managing User Accounts 39 5
- 7 Working with Portals 43 5
- 11 Configuring SAN Access 75 6
- 12 Troubleshooting the SAN 93 6
- A Glossary 107 7
- Description 11
- Using the SAN Client 12
- Event Logging 12
- 6 Description 14
- 8 Description 16
- Getting Started 17
- Before Installing AMC 18
- Installing the AMC Server 19
- 12 Getting Started 20
- Launching the AMC Server 21
- Installing the AMC Client 22
- Launching the AMC Client 23
- Connecting to the Server 24
- Logging on 25
- Logging off 26
- Exiting the AMC Client 27
- Shutting Down the AMC Server 27
- 20 Getting Started 28
- Frequently Asked Questions 29
- 22 Frequently Asked Questions 30
- How do I create policies? 31
- 24 Frequently Asked Questions 32
- The SAN Management Interface 33
- Received Event Trap Window 34
- Scalar i2000 38
- Device Numbering 40
- Graphical Panel 40
- Data Panel 41
- Max Speed 42
- Status/Message Area 43
- Common SAN Management Options 44
- Managing User Accounts 47
- 40 Managing User Accounts 48
- Adding a New User Account 49
- Modifying a User Account 50
- Deleting a User Account 50
- Working with Portals 51
- Modifying a Portal 52
- Deleting a Portal 53
- 46 Working with Portals 54
- Working with SAN Categories 55
- Creating a new Category 56
- Renaming a Category 56
- Deleting a Category 56
- Moving a Category 57
- Moving Items by Drag and Drop 57
- Working With Views 59
- Opening Saved Views 60
- Creating Views 60
- Saving Views 62
- Deleting Views 62
- Searching the Current View 62
- Reporting the Current View 63
- Configuring Email 65
- Configuring Policies 66
- Discovering the SAN 67
- Rediscovering a Segment 68
- Managing the SAN Appliance 69
- Refreshing Data 70
- Updating Firmware 72
- Using Restart 72
- Displaying RMU Data 73
- Managing the SCSI Channel 75
- Configuring the SCSI Channel 76
- Managing the Fibre Channel 77
- Resetting the Fibre Channel 78
- Configuring the Fibre Channel 78
- Managing a Device 80
- Editing Device Maps 81
- Pre-Assigning Device Numbers 82
- Configuring SAN Access 83
- Using Channel Zoning 84
- Data Mover Module 84
- Installing HRS 85
- 78 Configuring SAN Access 86
- 80 Configuring SAN Access 88
- Installing SFM 89
- 82 Configuring SAN Access 90
- Adding SFM Hosts 91
- Using eVPS 92
- Installing eVPS 93
- 86 Configuring SAN Access 94
- 88 Configuring SAN Access 96
- Deleting eVPS Hosts 97
- Using the eVPS View Menu 97
- Using VPM 98
- Making VPM assignments 99
- 92 Configuring SAN Access 100
- Troubleshooting the SAN 101
- Interpreting the Event Log 102
- 96 Troubleshooting the SAN 104
- Receiving Event Traps 105
- Monitoring the LED Panel 106
- Figure 21 SNC 4000 LED panel 107
- Figure 22 SNC 5100 LED panel 107
- Using Identify 108
- Monitoring Environmental Data 109
- Using Health Check 110
- Obtaining a Drive Dump 111
- Checking the Command Flow Log 112
- 106 Troubleshooting the SAN 114
- Glossary 115
- 108 Glossary 116
- 110 Glossary 118
- 112 Index 120
- 114 Index 122
Relacionado con productos y manuales para Software Quantum Scalar 1000
Software Quantum DX30 Guía de usuario
(58 paginas)
(58 paginas)
Software Quantum SuperLoader 3 Guía de usuario
(160 paginas)
(160 paginas)
Software Quantum SuperLoader Guía de usuario
(196 paginas)
(196 paginas)
Software Quantum Scalar i2000 Guía de usuario
(544 paginas)
(544 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales