Quantum SDLT 320 Guía de usuario Pagina 36
- Pagina / 102
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CHAPTER 2: General Drive Specifications SDLT 220 and SDLT 320 Design & Integration Guide
2-18 March 2004 81-81148-01
2.7.1 Temperature and Humidity
The ambient operating environment for the tape drive may not exceed the limits
shown in Table 2-11. (The specifications shown in the table are valid for both the
internal and tabletop tape drives.)
2.7.2 Air Flow Requirements
Adequate air flow must be provided for the internal unit to dissipate the heat
resulting from drive operation (see Chapter4, “Thermal Specifications” for more
details about temperatures inside the drive, and illustrations showing where air
flow and various temperatures are measured). The air flow must be sufficient to
keep the tape path temperature below 52°C.
NOTE: It is important to realize that the amount of air flow
provided for the tape drive determines the maximum
ambient temperature in which the drive can operate.
Table 2-11. Temperature and Humidity Specification
Specification Operating Limits
Non-Operating Limits
(Power On; No Tape Loaded)
Wet Bulb Temperature 25°C (77°F) 25°C (77°F)
Dry Bulb Temperature
Range
10°C to 40°C (50°F to 104°F) 10°C to 40°C (50°F to 104°F)
Temperature Gradient 11°C (20°F) / hour (across range) 15°C (27°F) / hour (across range)
Relative Humidity 20% to 80% (non-condensing) 10% to 90% (non-condensing)
Humidity Gradient 10% / hour 10% / hour
- Copyright 2
- Trademarks 2
- Legal Disclaimers 2
- Contact Information 2
- Revision History 3
- Table of Contents 5
- 81-81148-01 March 2004 vii 7
- List of Tables 9
- List of Figures 11
- Introduction 13
- 1.2 Referenced Documents 14
- 1.3 Related Documents 14
- 1.4 Structure of this Manual 15
- 1.5 Conventions 16
- 1.6 For More Information 17
- 1.7 Reader Comments 17
- 1.8 Quantum Diagnostics Tools 18
- General Drive 19
- Specifications 19
- 2.2 SDLT Product Features 20
- 1 Amber LED 21
- 2 Green LED 21
- 3 Yellow LED 21
- 4 Eject Button 21
- 2.3 Dimensions and Tolerances 22
- 81-81148-01 March 2004 2-5 23
- 2-6 March 2004 81-81148-01 24
- 2.4 Physical Dimensions 25
- Orientation Looks Like This 26
- Typical (Top Side Up) 26
- Left Side Down 26
- Right Side Down 26
- 2.5 Reliability 27
- 2.5.4 Data Integrity 28
- Mechanism 29
- 2.6 Functional Specifications 30
- 81-81148-01 March 2004 2-13 31
- 2-14 March 2004 81-81148-01 32
- 2.6.5 Storage Capacity 33
- 2-16 March 2004 81-81148-01 34
- 81-81148-01 March 2004 2-17 35
- 2.7.2 Air Flow Requirements 36
- 2.7.3 Storage and Shipment 37
- 2.7.4 Altitude 37
- 2-20 March 2004 81-81148-01 38
- ≤ 20 lbs 39
- ≤ 50 lbs 39
- 2-22 March 2004 81-81148-01 40
- 81-81148-01 March 2004 2-23 41
- 2-24 March 2004 81-81148-01 42
- • Cleaning Requested 43
- • Cleaning Required 43
- • Cleaning Tape Expired 43
- SCSI Cleaning Error Reporting 44
- Figure 2-7. Front Panel LEDs 45
- 2-28 March 2004 81-81148-01 46
- Electrical Specifications 47
- 3-2 March 2004 81-81148-01 48
- 3.2 Power Supply Tolerances 49
- 3-4 March 2004 81-81148-01 50
- Thermal Specifications 51
- 4.2 Air Flow Measurements 52
- 81-81148-01 March 2004 4-3 53
- 4-4 March 2004 81-81148-01 54
- 81-81148-01 March 2004 4-5 55
- 4-6 March 2004 81-81148-01 56
- 81-81148-01 March 2004 4-7 57
- SDLT 320 58
- Embedded Bezel 59
- Library Bezel 60
- Regulatory Requirements 61
- 5.1.2 Safety Requirements 62
- 81-81148-01 March 2004 5-3 63
- 5.2.3 Conducted Emissions 64
- 5.2.4 Radiated Emissions 64
- Quantum tape drive products 65
- 5.3 Acoustic Noise Emissions 66
- SCSI and Controller 67
- Interface Specification 67
- 6.2 Setting the SCSI ID 68
- 81-81148-01 March 2004 6-3 69
- 6-4 March 2004 81-81148-01 70
- 6.3 Hardware (Connectors) 71
- 6.4 SCSI Stub Lengths 72
- 6.5 SCSI Cable Length 72
- 6.6 Power On Self Test 73
- 6.7 SCSI Command Timeout 73
- 6-8 March 2004 81-81148-01 74
- 6.8 SCSI and Power Connectors 75
- • Connector body: 51110-0850 76
- Figure 6-4. Loader Connector 76
- (Internal Version Shown) 76
- 81-81148-01 March 2004 6-11 77
- 6-12 March 2004 81-81148-01 78
- 81-81148-01 March 2004 6-13 79
- 6-14 March 2004 81-81148-01 80
- 81-81148-01 March 2004 6-15 81
- 6.10 Configuring the Drive 82
- Updating the Firmware 83
- 7.1.2 Making a FUP/CUP Tape 84
- 7.1.3 Using a CUP/FUP Tape 84
- 81-81148-01 March 2004 7-3 85
- Drive Interface 86
- • Updating the same revision 87
- 7-6 March 2004 81-81148-01 88
- Insertion and Extraction 89
- Guidelines 89
- 8.1.1 General Status Packet 90
- 8.1.2 Loading a Tape 91
- 8.1.3 Unloading a Tape 92
- Configuration) 93
- 81-81148-01 March 2004 8-7 95
- Insertion Depth 97
- Cartridge Insertion Force 97
- Insertion Velocity 97
- Debounce Time 98
- Initialization Time 98
- 81-81148-01 March 2004 8-11 99
- Eject Distance 100
- Cartridge Extraction Force 100
- Extraction Velocity 100
- 81-81148-01 A02 102
Relacionado con productos y manuales para Cargadores automáticos de cinta y bibliotecas Quantum SDLT 320
(294 paginas)
(222 paginas)
(34 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales