Quantum Scalar 100 Guía de usuario Pagina 64
- Pagina / 126
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
7-54 6-00667-01 Rev B
Scalar 100
Exporting a Tape Cartridge
Use Export to remove tape cartridges from your library through the Mailbox. Export takes a specific
tape cartridge and places it in the Mailbox so that you can remove it from your library. To use this
procedure, the Mailbox cannot be configured as storage.
Path: Main menu > Command > Mailbox > Export
To export tape cartridges
1. From the Main menu, select Command and then select Mailbox. Select Export.
2. Select OK.
The panel shows a list of tape cartridges in the library.
3. Press Select to begin choosing the tape cartridge(s) you want to export.
4. Use Next, Select, and Pages to choose the tape cartridge(s) you want to export.
Highlighted cartridges will be exported. You can only export as many tape cartridges as your
Mailbox holds.
5. When complete, press OK.
Manually Removing Tape Cartridges
If you need to remove a large number of tape cartridges, you probably will want to manually remove
them. If you only have a small number of tape cartridges to remove, use the Export command as
it does not interfere with library operations. To do this procedure, the front door must be unlocked
or you must have the key.
To manually remove tape cartridges
1. Place the library in an offline state.
See Using Commands that Require an Offline State on page 5-38.
2. If the library door is locked, unlock the door. Open the door, and remove the tape cartridges.
3. Close the door. (Lock it if necessary.)
The library executes the TEACH and INVENTORY procedures.
Working with Cleaning Cartridges
The AutoClean menu allows you to import and export cleaning cartridges. It also provides you
access to cleaning cartridge information.
For information about how cleaning drives, see Configuring Drive Cleaning on page 8-60
.
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Relacionado con productos y manuales para Cargadores automáticos de cinta y bibliotecas Quantum Scalar 100
(16 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales