Quantum Scalar 100 Guía de usuario Pagina 81
- Pagina / 126
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Maintaining your Library 9-71
Scalar 100
Running a Demo
Use Demo to run a demonstration routine. This command is helpful for testing new library
configurations to ensure all the components are interacting correctly.
Path: Main menu > More > Service > Library > Exercise > Demo
To run a demo
1. From the Main menu, select More. Select Service and then select Library. Select Exercise
and then Demo.
2. Use Up, Down, Next, Change, and Yes/No to complete the following fields:
• Demo Mode — specifies the type of demonstration to run. Possible values are Cycle or
Time.
• Cycle — specifies running the demonstration based on the number of completed
cycles.
• Time — specifies running the demonstration based on time elapsed.
• Cycles to run — specifies the number of cycles the demonstration will be run. This option
is only available if Cycle was specified. Possible values are 0 to 9999.
• Hours to run — specifies the number of hours to run the demonstration. This option is only
available if Time was specified. Possible values are 2 hour increments up to 24 hours.
• Include Drives — specifies whether or not to include drives in the demonstration.
• Mailbox — specifies whether or not to include the Mailbox in the demonstration.
3. Select OK.
The demonstration runs. A status menu is displayed during the demonstration.
4. When complete, select OK.
Running a Self Test
Use Self Test to run a series of pre-programed tests that exercise the integrity of the system.
Path: Main menu > More > Service > Library > Exercise > Self Test
To run Self Test
1. From the Main menu, select More. Select Service and then select Library. Select Exercise
and then Self Test.
2. Use Up, Down, Next, and Yes/No to complete the following fields:
• Cycles to run — specifies the number of times to run the Self Test.
• Include drives — specifies whether or not to include the drives.
CAUTION:
This command could potentially move a cartridge into an incorrect
partition, if the library has been partitioned by the host.
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Relacionado con productos y manuales para Cargadores automáticos de cinta y bibliotecas Quantum Scalar 100
(16 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales