Quantum DLT 7 Manual Pagina 96
- Pagina / 177
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 9 Installing an Internal SCSI Tape Drive
Confirming the Installation
DLT-S4 Product Manual 78
Confirming the Installation 9
To confirm the installation, turn on the host computer.
The screens displayed at power-on contain:
•BIOS
•Operating system
• SCSI controller information
If the first screen displays host adapter and SCSI ID information
indicating the drive is a Quantum product, then the installation was
successful.
If the installation was NOT successful, see POST and SCSI
Troubleshooting on page 124.
Adding an Additional Device 9
Once you have successfully confirmed the installation of your tape drive,
you may add one additional device to the SCSI bus.
1 Ensure that all devices have unique SCSI IDs (see Setting the SCSI ID
on page 69).
2 Ensure that the tape drive, host computer, and all peripheral devices
(such as printers) are turned off.
3 Make sure that all the SCSI cables and terminators are SPI-4 (or SPI-5)
compatible.
Note: Use care when connecting the cables to avoid bending or
damaging the connector pins.
Caution: Never connect the tape drive while the tape drive,
host system, or peripheral devices are turned on.
Doing so could result in damage to the tape drive or
other peripheral devices.
- '/76 1
- Contents 3
- Chapter 3 Cartridges 19 4
- Chapter 4 Specifications 37 4
- DLT-S4 Product Manual v 5
- DLT-S4 Product Manual vi 6
- DLT-S4 Product Manual vii 7
- Glossary 144 8
- Index 153 8
- DLT-S4 Product Manual ix 9
- DLT-S4 Product Manual x 10
- DLT-S4 Product Manual xi 11
- DLT-S4 Product Manual xii 12
- DLT-S4 Product Manual xiii 13
- DLT-S4 Product Manual xiv 14
- DLT-S4 Product Manual xv 15
- Product Overview 19
- Tape Drive Models 1 20
- Chapter 1 Product Overview 21
- Tape Drive Models 21
- DLT-S4 Product Manual 3 21
- Figure 2 Tabletop Tape Drive 21
- Tape Drive Features 1 22
- Maximum Data Transfer Rate 1 23
- Functional Specifications 1 24
- Tape Drive Technology 1 25
- Tape Drive Components 1 26
- Tape Drive Components 27
- DLT-S4 Product Manual 9 27
- Integrated 28
- Interface Types 1 29
- Interface Types 30
- DLT-S4 Product Manual 12 30
- Physical Characteristics 30
- Before You Begin 31
- Warranty Note 2 32
- Safety Precautions 2 32
- Chapter 2 Before You Begin 33
- DLT-S4 Product Manual 15 33
- DLT-S4 Product Manual 16 34
- Figure 4 Receiver Area 34
- Pre-Installation Guidelines 2 35
- Cartridges 37
- Chapter 3 Cartridges 38
- DLT-S4 Product Manual 20 38
- Figure 5 Compatible Tape 38
- ≥ 18.0 MB/sec 40
- ≥ 8.0 MB/sec 40
- DLT-S4 Product Manual 23 41
- DLT-S4 Product Manual 24 42
- Inspecting a Cartridge 3 43
- Spring-loaded hub 44
- Reel lock 44
- Write-protecting a Cartridge 49
- DLT-S4 Product Manual 31 49
- Table 22 Write-protect Tab 49
- Positions 49
- Loading a Cartridge 3 50
- Unloading a Cartridge 3 51
- DLTSage WORM 3 52
- Specifications 55
- Physical Specifications 4 56
- Dimensions and Weights 4 57
- Acoustic Noise Emissions 4 60
- Common Interface 61
- Information 61
- SCSI Command Timeout 5 62
- Rear Panel Connectors 5 64
- Rear Panel Connectors 65
- DLT-S4 Product Manual 47 65
- Figure 14 ADI/Loader Port 65
- Interface Schematic 65
- Parallel SCSI Interface 66
- Rear Panel Connectors 6 67
- SCSI Cable Connectors 6 67
- SCSI Tape Drive Features 6 68
- SCSI Stub and Cable Lengths 6 68
- DLT-S4 Product Manual 52 70
- DLT-S4 Product Manual 54 72
- Fibre Channel Interface 73
- Rear Panel Connectors 7 74
- DLT-S4 Product Manual 57 75
- Connector 75
- Practical Considerations 7 76
- World-wide Names 7 79
- Serial Attached SCSI (SAS) 80
- Interface 80
- Rear Panel Connectors 8 81
- SAS Cable Connector 8 82
- SAS Tape Drive Features 8 82
- Practical Considerations 8 82
- SAS Tape Drive Speed 8 83
- World-wide Names 8 83
- Installing an Internal 84
- SCSI Tape Drive 84
- Equipment Required 9 85
- Installation Steps 9 85
- Rear Panel Connectors 9 86
- Unpacking the Tape Drive 9 87
- Setting the SCSI ID 9 87
- DLT-S4 Product Manual 73 91
- Built-in 93
- Terminator 93
- SCSI cable (shown with 94
- Setting TERMPWR 9 95
- Adding an Additional Device 9 96
- Installing an Internal Fibre 98
- Channel Tape Drive 98
- Equipment Required 10 99
- Installation Steps 10 99
- Rear Panel Connectors 10 100
- Unpacking the Tape Drive 10 101
- Mounting holes 102
- DLT-S4 Product Manual 85 103
- Holes — Bottom View 103
- Connecting the Cables 10 104
- DLT-S4 Product Manual 87 105
- Channel and Power Cables 105
- Confirming the Installation 105
- Adding Additional Devices 10 106
- Installing an Internal SAS 107
- Tape Drive 107
- Equipment Required 11 108
- Installation Steps 11 108
- Rear Panel Connectors 11 109
- Unpacking the Tape Drive 11 110
- DLT-S4 Product Manual 94 112
- Connecting the Cables 11 113
- DLT-S4 Product Manual 96 114
- Adding Additional Devices 11 115
- Installing the Tabletop 116
- Equipment Required 12 117
- Installation Steps 12 117
- Rear Panel Connectors 12 118
- DLT-S4 Product Manual 101 119
- Setting the SCSI ID 12 120
- Terminating the SCSI Bus 121
- SCSI cable 123
- 220V / 240V 124
- Configuring the Tape Drive 12 127
- Using TERMPWR 12 127
- Using the Tape Drive 128
- Eject button 129
- Left LED 129
- Middle LED 129
- Right LED 129
- Power-On Self-Test 13 131
- Performing a Trial Backup 13 133
- Cleaning the Tape Drive 13 137
- DLT-S4 Product Manual 121 139
- DLT-S4 Product Manual 122 140
- Troubleshooting 141
- Chapter 14 Troubleshooting 143
- POST and SCSI Troubleshooting 143
- DLT-S4 Product Manual 125 143
- Table 37 POST and SCSI 143
- Troubleshooting Guidelines 143
- DLT-S4 Product Manual 126 144
- DLT-S4 Product Manual 127 145
- Over Temperature Condition 14 146
- Preparing the Tape 147
- Drive for Shipping 147
- Power off the tape drive 148
- Diagnostic Tools 149
- Accessing the Tools 1 150
- Device Drivers 1 150
- TapeAlert 1 151
- Medium Auxiliary Memory 1 151
- DLTSage 1 152
- Appendix A Diagnostic Tools 153
- DLT-S4 Product Manual 135 153
- Environmental Compliance 155
- DLT-S4 Product Manual 138 156
- Regulatory Statements 157
- Taiwan Statement 3 158
- DLT-S4 Product Manual 141 159
- Laser Statement 3 160
- Power Cord Statement 3 161
- Glossary 162
- Numerics 171
Relacionado con productos y manuales para Las unidades de cinta Quantum DLT 7
Las unidades de cinta Quantum DLT 8000 Manual
(408 paginas)
(408 paginas)
Las unidades de cinta Quantum LTO-6 Guía de usuario
(38 paginas)
(38 paginas)
Las unidades de cinta Quantum 3U Manual de usuario
(16 paginas)
(16 paginas)
Las unidades de cinta Quantum LTO 4 Guía de usuario
(98 paginas)
(98 paginas)
Las unidades de cinta Quantum DLT 7000 Manual
(312 paginas)
(312 paginas)
Las unidades de cinta Quantum DLT 2500 Manual
(12 paginas)
(12 paginas)
Las unidades de cinta Quantum DLT 4000 Manual
(300 paginas)
(300 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales