Quantum DLT 8000 Manual Pagina 175
- Pagina / 408
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SCSI Commands
Quantum DLT 8000 Tape System 5-31
INQUIRY Command (12h) (continued)
Table 5–13 Command Support Data Page — Field Descriptions
Field Description
Support The value of the Support field describes the type of support that the
tape drive provides for Command Support Data.
Value Description
000b Data about the requested SCSI operation code is not currently
available. In this case, all data after Byte 1 is undefined.
001b The device does not support the SCSI operation code requested.
In this case, all data after Byte 1 is undefined
010b Reserved
011b The device supports the SCSI operation code in conformance
with the SCSI standard.
100b Vendor-Specific
101b The device supports the SCSI operation code, but in a vendor-
specific manner
110b Vendor-Specific
111b Reserved
ISO-Version Must be 0.
ECMA-Version Must be 0.
ANSI-Approved Minimum operating definition for supported command.
Version
CDB Size This field contains the number of bytes in the CDB for the Operation
Code being requested and the size of the CDB Usage Data in the data
that is returned in response to the INQUIRY.
CDB Usage Data This field contains information about the CDB for the Operation Code
being queried. Note that the first byte of the CDB Usage Data contains
the OpCode for the operation specified. All of the other bytes of the
CDB Usage Data contain a map for bits in the CDB of the OpCode
specified.
NOTE
The bits in the map have a 1-to-1 correspondence to the CDB for the
OpCode being queried. That is, if the device senses a bit as the entire field
or as part of the field of the operation, the map in CDB Usage Data contains
a 1 in the corresponding bit position. If the device ignores a bit or declares
a bit as “reserved” in the CDB for the OpCode being queried, the map has a
0 in that corresponding bit position.
- 8000 Tape System 1
- Product Manual 1
- Table of Contents 10
- REVISION HISTORY 27
- Revision History 28
- Quantum DLT 8000 Tape System 28
- ABOUT THIS MANUAL 33
- CONVENTIONS 35
- FOR MORE INFORMATION 35
- READER COMMENTS 35
- About This Manual 36
- Chapter 1 37
- 1.3 SPECIFICATIONS 38
- 1.3.4 Reliability (Projected) 41
- 1.3.5 Physical Specifications 41
- 1.3.7 Operating Air Velocity 43
- 1.3.9 Altitude 45
- 1.3.10 Acoustic Emissions 46
- 1.3.12 Power Requirements 47
- 1.3.13 Current Requirements 48
- TAPE SYSTEM 55
- 2.2.1 Setting the SCSI ID 58
- 2.2.2 Setting TERM PWR 60
- Front Bezel 61
- 2.3.1 Selecting SCSI ID 71
- SCSI Connectors (2) 72
- 220 / 240 V 74
- AC Power Cord Connector 75
- 2.4 The Tape Cartridge 76
- 2.4.4 Loading a Cartridge 82
- 2.4.5 Unloading a Cartridge 84
- 2.5.1 Unload Button 88
- 2.5.3 Selecting Density 89
- 2.9 Troubleshooting 99
- SCSI DESCRIPTION 103
- 3.2 SCSI Commands 104
- SCSI Description 105
- 3.3 Signal States 107
- 3.4 SCSI Signals 109
- 3.4.2 Signal Bus Timing 110
- 3.5 SCSI Bus Phases 113
- Bus Free Sequence 114
- 3.5.2 ARBITRATION Phase 115
- Arbitration Sequence 115
- 3.5.3 SELECTION Phase 116
- Selection Sequence 116
- Selection Time-Out 117
- 3.5.4 RESELECTION Phase 117
- Reselection Sequence 117
- SCSI ID bit 118
- Reselection Time-Out 120
- 3.6 SCSI Bus Conditions 128
- 3.6.2 Reset Condition 129
- 3.6.3 Queued Unit Attentions 130
- Chapter 4 131
- MESSAGES 131
- Messages 132
- 4.2 Supported SCSI Messages 135
- 4.2.12 NO OPERATION (08h) 141
- SCSI COMMANDS 145
- SCSI Commands 146
- 5.1.1 SCSI Pointers 147
- 5.1.3 Status/Error Reporting 151
- (Continued) 153
- 5.3 ERASE Command (19h) 159
- 5.4 INQUIRY Command (12h) 161
- 5.6 LOCATE Command (2Bh) 179
- 5.7 LOG SELECT Command (4Ch) 181
- Page Code Page Description 183
- 02h Write Error Counter Page 183
- 03h Read Error Counter Page 183
- 32h Compression Ratio Page 183
- LOG PAGE HEADER 184
- LOG PARAMETERS 185
- (continued) 186
- 5.8 LOG SENSE Command (4Dh) 189
- Descriptions (continued) 196
- 5.8.5 TapeAlert Page (2Eh) 200
- TAPE ALERT LOG PAGE HEADER 200
- TAPE ALERT LOG PARAMETERS 201
- Descriptions 210
- 5.9.1 Mode Parameter List 217
- 5.9.8 TAPEALERT PAGE (1Ch) 237
- FORCEDENSITY parameter to 4 247
- 5.10.3 MODE SENSE Mode Pages 258
- Data Field Description 284
- 5.14 READ Command (08h) 304
- 5.16.2 Data Mode 311
- 5.16.3 Descriptor Mode 311
- 5.26 REWIND Command (01h) 353
- 5.28 SPACE Command (11h) 360
- 5.30 VERIFY Command (13h) 363
- 5.31 WRITE Command (0Ah) 364
- 5.32.2 Write Data Mode (010b) 368
- INFORMATION 373
- Appendix B 377
- B.2 Bugcheck Packets 378
- B.2.1 POST Failure Packets 379
- B.2.2 Event Log Packets 379
- UPDATING THE FIRMWARE 381
- 1. POST passed 383
- 2. The drive is unloaded 383
- THE LIBRARY PORT 387
- CARTRIDGES 389
- Cartridge 391
- SYSTEM SCSI COMMANDS 397
- DLT 7000 EMULATION FEATURE 399
- SCSI Bus Differences 403
- Front Panel Differences 405
- *81-60118-04 A01* 408
Relacionado con productos y manuales para Las unidades de cinta Quantum DLT 8000
Las unidades de cinta Quantum LTO-6 Guía de usuario
(38 paginas)
(38 paginas)
Las unidades de cinta Quantum 3U Manual de usuario
(16 paginas)
(16 paginas)
Las unidades de cinta Quantum LTO 4 Guía de usuario
(98 paginas)
(98 paginas)
Las unidades de cinta Quantum DLT 7000 Manual
(312 paginas)
(312 paginas)
Las unidades de cinta Quantum DLT 2500 Manual
(12 paginas)
(12 paginas)
Las unidades de cinta Quantum DLT 4000 Manual
(300 paginas)
(300 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales