Quantum DLT 8000 Manual Pagina 405
- Pagina / 408
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix G: DLT 7000 Emulation Feature
Quantum DLT 8000 Tape System G-7
DLT 7000 Drive DLT 8000 Drive
DLT 8000 Drive with
DLT 7000 Emulation
Enabled
Page C1h
• Vendor Unique DLT 7000 Format
Support
DLT 8000 Format
Support
DLT 8000 Format
Support (Product
Family 0x09)
READ POSITION
Command
• Long Format Bit Not supported Supported Supported
SEND DIAGNOSTIC
Command
• Run Basic Health
Check (BHC) Pattern
Number Not supported Supported Supported
Detailed Unit Attention
ASCQs for Resets Not supported Supported Supported
Front Panel Differences
The table below describes the difference between the front panels of a “real” DLT 7000
drive, a DLT 8000 drive, and a DLT 8000 drive with DLT 7000 emulation enabled.
DLT 7000 Drive DLT 8000 Drive
DLT 8000 with DLT 7000
Emulation Enabled
Density Select
40GB
35GB
20GB
10/15GB
6.0GB
2.6GB
Not supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Selection Not Available
Selection Not Available
Not supported
Supported
Supported
Supported
Selection Not Available
Selection Not Available
Run BHC Test Not supported Supported Supported
NOTE
DLT 8000 Front Panel
The 40/80 GB density light and selection are not available when a DLT 8000 drive
is running in DLT 7000 emulation mode. The 40/80 GB density selection is
skipped in the selection sequence.
- 8000 Tape System 1
- Product Manual 1
- Table of Contents 10
- REVISION HISTORY 27
- Revision History 28
- Quantum DLT 8000 Tape System 28
- ABOUT THIS MANUAL 33
- CONVENTIONS 35
- FOR MORE INFORMATION 35
- READER COMMENTS 35
- About This Manual 36
- Chapter 1 37
- 1.3 SPECIFICATIONS 38
- 1.3.4 Reliability (Projected) 41
- 1.3.5 Physical Specifications 41
- 1.3.7 Operating Air Velocity 43
- 1.3.9 Altitude 45
- 1.3.10 Acoustic Emissions 46
- 1.3.12 Power Requirements 47
- 1.3.13 Current Requirements 48
- TAPE SYSTEM 55
- 2.2.1 Setting the SCSI ID 58
- 2.2.2 Setting TERM PWR 60
- Front Bezel 61
- 2.3.1 Selecting SCSI ID 71
- SCSI Connectors (2) 72
- 220 / 240 V 74
- AC Power Cord Connector 75
- 2.4 The Tape Cartridge 76
- 2.4.4 Loading a Cartridge 82
- 2.4.5 Unloading a Cartridge 84
- 2.5.1 Unload Button 88
- 2.5.3 Selecting Density 89
- 2.9 Troubleshooting 99
- SCSI DESCRIPTION 103
- 3.2 SCSI Commands 104
- SCSI Description 105
- 3.3 Signal States 107
- 3.4 SCSI Signals 109
- 3.4.2 Signal Bus Timing 110
- 3.5 SCSI Bus Phases 113
- Bus Free Sequence 114
- 3.5.2 ARBITRATION Phase 115
- Arbitration Sequence 115
- 3.5.3 SELECTION Phase 116
- Selection Sequence 116
- Selection Time-Out 117
- 3.5.4 RESELECTION Phase 117
- Reselection Sequence 117
- SCSI ID bit 118
- Reselection Time-Out 120
- 3.6 SCSI Bus Conditions 128
- 3.6.2 Reset Condition 129
- 3.6.3 Queued Unit Attentions 130
- Chapter 4 131
- MESSAGES 131
- Messages 132
- 4.2 Supported SCSI Messages 135
- 4.2.12 NO OPERATION (08h) 141
- SCSI COMMANDS 145
- SCSI Commands 146
- 5.1.1 SCSI Pointers 147
- 5.1.3 Status/Error Reporting 151
- (Continued) 153
- 5.3 ERASE Command (19h) 159
- 5.4 INQUIRY Command (12h) 161
- 5.6 LOCATE Command (2Bh) 179
- 5.7 LOG SELECT Command (4Ch) 181
- Page Code Page Description 183
- 02h Write Error Counter Page 183
- 03h Read Error Counter Page 183
- 32h Compression Ratio Page 183
- LOG PAGE HEADER 184
- LOG PARAMETERS 185
- (continued) 186
- 5.8 LOG SENSE Command (4Dh) 189
- Descriptions (continued) 196
- 5.8.5 TapeAlert Page (2Eh) 200
- TAPE ALERT LOG PAGE HEADER 200
- TAPE ALERT LOG PARAMETERS 201
- Descriptions 210
- 5.9.1 Mode Parameter List 217
- 5.9.8 TAPEALERT PAGE (1Ch) 237
- FORCEDENSITY parameter to 4 247
- 5.10.3 MODE SENSE Mode Pages 258
- Data Field Description 284
- 5.14 READ Command (08h) 304
- 5.16.2 Data Mode 311
- 5.16.3 Descriptor Mode 311
- 5.26 REWIND Command (01h) 353
- 5.28 SPACE Command (11h) 360
- 5.30 VERIFY Command (13h) 363
- 5.31 WRITE Command (0Ah) 364
- 5.32.2 Write Data Mode (010b) 368
- INFORMATION 373
- Appendix B 377
- B.2 Bugcheck Packets 378
- B.2.1 POST Failure Packets 379
- B.2.2 Event Log Packets 379
- UPDATING THE FIRMWARE 381
- 1. POST passed 383
- 2. The drive is unloaded 383
- THE LIBRARY PORT 387
- CARTRIDGES 389
- Cartridge 391
- SYSTEM SCSI COMMANDS 397
- DLT 7000 EMULATION FEATURE 399
- SCSI Bus Differences 403
- Front Panel Differences 405
- *81-60118-04 A01* 408
Relacionado con productos y manuales para Las unidades de cinta Quantum DLT 8000
Las unidades de cinta Quantum LTO-6 Guía de usuario
(38 paginas)
(38 paginas)
Las unidades de cinta Quantum 3U Manual de usuario
(16 paginas)
(16 paginas)
Las unidades de cinta Quantum LTO 4 Guía de usuario
(98 paginas)
(98 paginas)
Las unidades de cinta Quantum DLT 7000 Manual
(312 paginas)
(312 paginas)
Las unidades de cinta Quantum DLT 2500 Manual
(12 paginas)
(12 paginas)
Las unidades de cinta Quantum DLT 4000 Manual
(300 paginas)
(300 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales