Quantum P1000 Guía de usuario descargar pdf (Pagina 52)

Chapter 2 Installing the P1000 Library

Connecting Host Computers

36 ATL P1000 Series User’s Guide

In the single-host configuration (see figure 26), the host computer is

connected to the host connector on the rear panel of the library. Since

there is only one SCSI bus, use all of the SCSI cables from the

accessories kit to daisy-chain the library to each of the tape drives.

Figure 26 Single-Host

SCSI Configuration

Host connector

15 in. (38 cm)

Terminator

P1000 back panel

21 in. (53 cm)

7 in. (18 cm)

To host computer

SCSI cables

SCSI cable

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 131 132

User’s Guide 1
Audience 13
Document 13
Organization 13
Table 1 Related 14
Documentation 14
Library Description 17
Chapter 1 Library Description 18
Figure 2 P1000 Front 18
View, Rack-mount Library 18
Configuration Options 19
Figure 3 P1000 Library 20
Back View 20
Library Elements 21
Figure 4 Library Elements 22
Robotics Operation 23
Front Panel 24
PRODUCTS 25
Load Port 26
Load and Bulk Packs 26
Back Panel 27
Tape Drives 28
Installing the P1000 Library 29
Site Requirements 30
Floor Clearance 31
Floor Strength and 31
Inclination 31
Overhead Clearance 31
Power and Grounding 31
Figure 11 AC Power 32
Receptacle 32
Unpacking the P1000 33
Uncrating the Library 34
Checking the 36
Contents 36
Preparing and Inserting Tape 46
Cartridges 46
Orange tab 48
Write-protect switch 48
Placing Tape 50
Cartridges in the Load 50
Connecting Host Computers 51
Figure 26 Single-Host 52
SCSI Configuration 52
Figure 28 Five-Host SCSI 54
Configuration 54
Turning On the Library 55
Table 3 Sample Library 56
Basic Operations 57
Chapter 3 Basic Operations 59
Using the GUI 59
Table 4 Vertical Bar 59
Buttons and Indicators 59
Table 6 GUI Screens 61
Figure 31 GUI Screens 61
Obtaining Library Status 62
Activity 63
Load Pack 64
Tapes Screen 64
Performing Manual Operations 67
Opening the Library 70
Manually Ejecting a 71
Cartridge 71
Operator Commands 73
Configure 76
Configuring Library Options 78
Performing an Inventory 82
Calibrating the Library 83
Chapter 4 Operator Commands 84
Exercising the Library 85
Unloading the Load Port 87
Service Commands 89
Performing a Service 96
Calibration 96
Chapter 5 Service Commands 97
Reenter the new password 100
Press the Execute button 100
Troubleshooting 101
Start-up Problems 102
GUI Problems 103
Robotics Problems 104
Operating Problems 106
Tape Drive Problems 108
Specifications 109
Appendix A Specifications 110
Table 16 Environmental 110
Rack Current Rating 114
Consideration 114
Grounding 114
Temperature 114
Procedure 115
Procedure (continued) 116
Figure 55 Installing the 118
Slide Assembly in the Rack 118
Adjusting the Slide Assembly 119
Adjusting the Slide 121
Assembly Tray on the 121
Slide Rails 121
Glossary 125

Comentarios a estos manuales

Sin comentarios

Quantum P1000 Guía de usuario Pagina 52

Comentarios a estos manuales

Relacionado con productos y manuales para Cargadores automáticos de cinta y bibliotecas Quantum P1000