Quantum SDLT 320 Manual de usuario Pagina 107
- Pagina / 150
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SDLT 220 and SDLT 320 Product Manual CHAPTER 6: SCSI Description
81-85002-01 March 2004 6-11
Disconnection Delay 200 µs Minimum time that a drive waits after releasing BSY before
participating in an ARBITRATION when honoring a
DISCONNECT message from the initiator.
Hold Time 45 ns Minimum time added between the assertion of REQ or ACK and
changing the data lines to provide hold time in the initiator or
drive while using standard (slow) synchronous data transfers.
Negation Period 90 ns Minimum time that a drive negates REQ while using
synchronous data transfers; also, the minimum time than an
initiator negates ACK while using synchronous data transfers.
1
Power-On to Selection
10 s
1
Recommended maximum time from power application until a
drive is able to respond with appropriate status and sense data to
the TEST UNIT READY, INQUIRY, and REQUEST SENSE
commands.
Reset to Selection Time
250 ms
1
Recommended maximum time after a hard RESET condition
until a drive is able to respond with appropriate status and sense
data to the TEST UNIT READY, INQUIRY, and REQUEST
SENSE commands.
Reset Hold Time 25 µs Minimum time for which RST is asserted; there is no maximum
time.
Selection Abort Time 200 µs Maximum time that a drive (or initiator) takes from its most
recent detection of being selected (or reselected) until asserting a
BSY response.
Selection Time-Out
Delay
250 ms
1
Recommended minimum time a SCSI device should wait for a
BSY response during SELECTION or RESELECTION before
starting the time-out procedure.
Transfer Period
2
100 ns <
time
< 500 ns
Minimum time allowed between the leading edges of successive
REQ pulses and of successive ACK pulses while using standard
or fast synchronous data transfers. The period range is 200 to
500ns minimum, standard, or 100 to 500ns minimum, fast-
synchronous.
1. Recommended time.
2. Set during an SDTR message.
Table 6-5. SCSI Bus Timing Values (Continued)
- Copyright 2
- Trademarks 2
- Legal Disclaimers 2
- Contact Information 2
- Revision History 3
- 81-85002-01 March 2004 5
- Table of Contents 7
- 81-85002-01 March 2004 ix 9
- Glossary G-1 11
- List of Tables 13
- List of Figures 15
- Introduction 17
- 1.3 Related Documents 18
- 1.4 Structure of this Manual 18
- 1.5 Conventions 19
- 1.6 For More Information 19
- 1.7 Reader Comments 20
- SDLT 220/320 Product 21
- Information 21
- 2-2 March 2004 81-85002-01 22
- 2.3 SDLT 220/320 Technology 23
- 2.3.2 Pivoting Optical Servo 24
- Likelihood 25
- 2.3.6 Positive Engagement 25
- 2-6 March 2004 81-85002-01 26
- 2.4.1 Data Control Module 27
- 2.4.2 Tape Control Module 28
- 2.4.3 Front Panel Module 29
- 2-10 March 2004 81-85002-01 30
- Features 31
- 2.6 Quantum Diagnostics Tools 32
- 2.7 TapeAlert 33
- 2-14 March 2004 81-85002-01 34
- Drive Specifications 35
- 3.1.1 Interface Type 36
- 3.1.2 Physical Dimensions 36
- 3.1.3 Storage Capacity 37
- 3.1.4 Compression 37
- 3.1.5 Data Integrity 37
- 3.1.7 Head Life and MTBF 38
- 3.1.8 Media Durability 39
- 3.2 Functional Specifications 40
- Feature SDLT 220 SDLT 320 41
- 3-8 March 2004 81-85002-01 42
- 81-85002-01 March 2004 3-9 43
- Pulse Shape 44
- Vibration 44
- 81-85002-01 March 2004 3-11 45
- 3-12 March 2004 81-85002-01 46
- 3.3.1 Air Flow Requirements 47
- 3.3.3 Storage and Shipment 48
- 3.3.4 Altitude 49
- 3-16 March 2004 81-85002-01 50
- 81-85002-01 March 2004 3-17 51
- 3-18 March 2004 81-85002-01 52
- Installing Your Tape Drive 53
- 4.1.1 Safety Precautions 54
- 4.1.2 Handling 55
- 4-4 March 2004 81-85002-01 56
- 81-85002-01 March 2004 4-5 57
- Tape Drive 58
- 81-85002-01 March 2004 4-7 59
- SCSI ID0123 60
- SCSI ID 4 5 (default) 6 7 60
- SCSI ID891011 60
- SCSI ID 12 13 14 15 60
- Denotes Pin 1 orientation 61
- SCSI ID Jumper Across Pins: 62
- 9-10* 7-8 5-6 3-4 1-2 62
- 81-85002-01 March 2004 4-11 63
- 4-12 March 2004 81-85002-01 64
- 81-85002-01 March 2004 4-13 65
- 4-14 March 2004 81-85002-01 66
- 81-85002-01 March 2004 4-15 67
- 4-16 March 2004 81-85002-01 68
- 81-85002-01 March 2004 4-17 69
- 4-18 March 2004 81-85002-01 70
- 81-85002-01 March 2004 4-19 71
- Pin Number Signal Name 72
- 4.4.1 Configuring the Drive 73
- SCSI Cables 74
- AC Power Cable 75
- 4-24 March 2004 81-85002-01 76
- Using Your Tape Drive 77
- 5.1 Power On Self Test 78
- 81-85002-01 March 2004 5-3 79
- 5.3 Updating the Firmware 80
- 5.3.2 Making a FUP/CUP Tape 81
- 5.3.3 Using a CUP/FUP Tape 81
- • Updating the same revision 82
- 81-85002-01 March 2004 5-7 83
- 5-8 March 2004 81-85002-01 84
- 81-85002-01 March 2004 5-9 85
- DLTtape IV [includes DLT 1 86
- (Benchmark)] 86
- SDLT 220 87
- SDLT 320 87
- • The tape is moving 88
- 5.6 Density Selection 89
- 5-14 March 2004 81-85002-01 90
- 81-85002-01 March 2004 5-15 91
- 5-16 March 2004 81-85002-01 92
- 5.7 Troubleshooting 93
- 5-18 March 2004 81-85002-01 94
- 81-85002-01 March 2004 5-19 95
- 5-20 March 2004 81-85002-01 96
- SCSI Description 97
- 6-2 March 2004 81-85002-01 98
- 6.2 SCSI-2 Commands 99
- 6-4 March 2004 81-85002-01 100
- 6.3 SCSI-3 Commands 101
- 6.4 Parity 102
- 6.5 Signal States 102
- 81-85002-01 March 2004 6-7 103
- 6.6 SCSI Signals 104
- Signal Definition 105
- 6.6.2 Signal Bus Timing 106
- 1. Recommended time 107
- 6-12 March 2004 81-85002-01 108
- Regulatory Compliance 109
- 7.1.2 Safety Requirements 110
- 7.2.3 Conducted Emissions 111
- 7.2.4 Radiated Emissions 112
- Type Specifications Comments 113
- 7.3 Acoustic Noise Emissions 114
- Super DLTtape I 115
- Data Cartridge 115
- Super DLTtape Data Cartridges 116
- 81-85002-01 March 2004 A-3 117
- A-4 March 2004 81-85002-01 118
- 81-85002-01 March 2004 A-5 119
- A-6 March 2004 81-85002-01 120
- 81-85002-01 March 2004 A-7 121
- A-8 March 2004 81-85002-01 122
- 81-85002-01 March 2004 A-9 123
- A.5 Loading a Data Cartridge 124
- DLTtape I Data Cartridges 125
- A-12 March 2004 81-85002-01 126
- DLTtape IV Data 127
- Cartridge 127
- B-2 March 2004 81-85002-01 128
- 81-85002-01 March 2004 B-3 129
- B-4 March 2004 81-85002-01 130
- 81-85002-01 March 2004 B-5 131
- B-6 March 2004 81-85002-01 132
- 81-85002-01 March 2004 B-7 133
- B.4 Loading a Data Cartridge 134
- 81-85002-01 March 2004 B-9 135
- B-10 March 2004 81-85002-01 136
- Glossary 137
- G-2 March 2004 81-85002-01 138
- 81-85002-01 March 2004 G-3 139
- G-4 March 2004 81-85002-01 140
- 81-85002-01 March 2004 G-5 141
- G-6 March 2004 81-85002-01 142
- 81-85002-01 March 2004 G-7 143
- G-8 March 2004 81-85002-01 144
- 81-85002-01 March 2004 G-9 145
- G-10 March 2004 81-85002-01 146
- 81-85002-01 March 2004 G-11 147
- G-12 March 2004 81-85002-01 148
- 81-85002-01 A04 150
Relacionado con productos y manuales para Las unidades de cinta Quantum SDLT 320
Las unidades de cinta Quantum L500 Guía de usuario
(120 paginas)
(120 paginas)
Las unidades de cinta Quantum DLT4500 Manual de usuario
(360 paginas)
(360 paginas)
Las unidades de cinta Quantum DLT-V4 Manual
(28 paginas)
(28 paginas)
Las unidades de cinta Quantum DLT 7 Manual
(177 paginas)
(177 paginas)
Las unidades de cinta Quantum DLT 8000 Manual
(408 paginas)
(408 paginas)
Las unidades de cinta Quantum LTO-6 Guía de usuario
(38 paginas)
(38 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales