Quantum SDLT 320 Manual de usuario Pagina 75
- Pagina / 150
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SDLT 220 and SDLT 320 Product Manual CHAPTER 4: Installing Your Tape Drive
81-85002-01 March 2004 4-23
If the SDLT drive is one of several devices connected to the SCSI bus,
and it is the last device connected to the SCSI bus, attach the SCSI
terminator to one of the connectors on the back of the drive.
4. Align the appropriate SCSI cable to its matching connector on the drive.
Carefully connect the cable, to avoid bending or damaging the connector pins.
Check the SCSI cable and termination connections and ensure that they are
attached correctly and seated firmly.
5. Snap the wire cable clamps into place to secure the cables.
AC Power Cable
An AC power cord is supplied with each tabletop unit. Carefully inspect the power
cord and ensure that the cord is the appropriate cord for your country or region
based on the criteria below.
The AC power cord used with the tabletop unit must meet the following criteria:
• The power cord should be a minimum of 18/3 AWG, 60°C, type SJT or SVT.
• UL and CSA certified cordage rated for use at 250 VAC with a current rating
that is at least 125% of the current rating of the product.
• The AC plug must be terminated in a grounding-type male plug designed for
use in your country or region. It must also have marks showing certification
by an agency acceptable in your country or region.
• The tabletop unit cord connector must be an IEC type CEE-22 female
connector.
• The cord must be no longer than 4.5 meters (14.5 feet).
• The cord must be FCC compliant with emissions specifications.
Figure 4-8 on page 4-24 shows the AC power cord plug-end types for 115 VAC
and 220/240 VAC usage.
W
ARNING: Do not attempt to modify or use a tabletop 100–115
VAC power cord for 220–240 VAC input power.
Modifying the power cord in any way can cause
personal injury and severe equipment damage.
- Copyright 2
- Trademarks 2
- Legal Disclaimers 2
- Contact Information 2
- Revision History 3
- 81-85002-01 March 2004 5
- Table of Contents 7
- 81-85002-01 March 2004 ix 9
- Glossary G-1 11
- List of Tables 13
- List of Figures 15
- Introduction 17
- 1.3 Related Documents 18
- 1.4 Structure of this Manual 18
- 1.5 Conventions 19
- 1.6 For More Information 19
- 1.7 Reader Comments 20
- SDLT 220/320 Product 21
- Information 21
- 2-2 March 2004 81-85002-01 22
- 2.3 SDLT 220/320 Technology 23
- 2.3.2 Pivoting Optical Servo 24
- Likelihood 25
- 2.3.6 Positive Engagement 25
- 2-6 March 2004 81-85002-01 26
- 2.4.1 Data Control Module 27
- 2.4.2 Tape Control Module 28
- 2.4.3 Front Panel Module 29
- 2-10 March 2004 81-85002-01 30
- Features 31
- 2.6 Quantum Diagnostics Tools 32
- 2.7 TapeAlert 33
- 2-14 March 2004 81-85002-01 34
- Drive Specifications 35
- 3.1.1 Interface Type 36
- 3.1.2 Physical Dimensions 36
- 3.1.3 Storage Capacity 37
- 3.1.4 Compression 37
- 3.1.5 Data Integrity 37
- 3.1.7 Head Life and MTBF 38
- 3.1.8 Media Durability 39
- 3.2 Functional Specifications 40
- Feature SDLT 220 SDLT 320 41
- 3-8 March 2004 81-85002-01 42
- 81-85002-01 March 2004 3-9 43
- Pulse Shape 44
- Vibration 44
- 81-85002-01 March 2004 3-11 45
- 3-12 March 2004 81-85002-01 46
- 3.3.1 Air Flow Requirements 47
- 3.3.3 Storage and Shipment 48
- 3.3.4 Altitude 49
- 3-16 March 2004 81-85002-01 50
- 81-85002-01 March 2004 3-17 51
- 3-18 March 2004 81-85002-01 52
- Installing Your Tape Drive 53
- 4.1.1 Safety Precautions 54
- 4.1.2 Handling 55
- 4-4 March 2004 81-85002-01 56
- 81-85002-01 March 2004 4-5 57
- Tape Drive 58
- 81-85002-01 March 2004 4-7 59
- SCSI ID0123 60
- SCSI ID 4 5 (default) 6 7 60
- SCSI ID891011 60
- SCSI ID 12 13 14 15 60
- Denotes Pin 1 orientation 61
- SCSI ID Jumper Across Pins: 62
- 9-10* 7-8 5-6 3-4 1-2 62
- 81-85002-01 March 2004 4-11 63
- 4-12 March 2004 81-85002-01 64
- 81-85002-01 March 2004 4-13 65
- 4-14 March 2004 81-85002-01 66
- 81-85002-01 March 2004 4-15 67
- 4-16 March 2004 81-85002-01 68
- 81-85002-01 March 2004 4-17 69
- 4-18 March 2004 81-85002-01 70
- 81-85002-01 March 2004 4-19 71
- Pin Number Signal Name 72
- 4.4.1 Configuring the Drive 73
- SCSI Cables 74
- AC Power Cable 75
- 4-24 March 2004 81-85002-01 76
- Using Your Tape Drive 77
- 5.1 Power On Self Test 78
- 81-85002-01 March 2004 5-3 79
- 5.3 Updating the Firmware 80
- 5.3.2 Making a FUP/CUP Tape 81
- 5.3.3 Using a CUP/FUP Tape 81
- • Updating the same revision 82
- 81-85002-01 March 2004 5-7 83
- 5-8 March 2004 81-85002-01 84
- 81-85002-01 March 2004 5-9 85
- DLTtape IV [includes DLT 1 86
- (Benchmark)] 86
- SDLT 220 87
- SDLT 320 87
- • The tape is moving 88
- 5.6 Density Selection 89
- 5-14 March 2004 81-85002-01 90
- 81-85002-01 March 2004 5-15 91
- 5-16 March 2004 81-85002-01 92
- 5.7 Troubleshooting 93
- 5-18 March 2004 81-85002-01 94
- 81-85002-01 March 2004 5-19 95
- 5-20 March 2004 81-85002-01 96
- SCSI Description 97
- 6-2 March 2004 81-85002-01 98
- 6.2 SCSI-2 Commands 99
- 6-4 March 2004 81-85002-01 100
- 6.3 SCSI-3 Commands 101
- 6.4 Parity 102
- 6.5 Signal States 102
- 81-85002-01 March 2004 6-7 103
- 6.6 SCSI Signals 104
- Signal Definition 105
- 6.6.2 Signal Bus Timing 106
- 1. Recommended time 107
- 6-12 March 2004 81-85002-01 108
- Regulatory Compliance 109
- 7.1.2 Safety Requirements 110
- 7.2.3 Conducted Emissions 111
- 7.2.4 Radiated Emissions 112
- Type Specifications Comments 113
- 7.3 Acoustic Noise Emissions 114
- Super DLTtape I 115
- Data Cartridge 115
- Super DLTtape Data Cartridges 116
- 81-85002-01 March 2004 A-3 117
- A-4 March 2004 81-85002-01 118
- 81-85002-01 March 2004 A-5 119
- A-6 March 2004 81-85002-01 120
- 81-85002-01 March 2004 A-7 121
- A-8 March 2004 81-85002-01 122
- 81-85002-01 March 2004 A-9 123
- A.5 Loading a Data Cartridge 124
- DLTtape I Data Cartridges 125
- A-12 March 2004 81-85002-01 126
- DLTtape IV Data 127
- Cartridge 127
- B-2 March 2004 81-85002-01 128
- 81-85002-01 March 2004 B-3 129
- B-4 March 2004 81-85002-01 130
- 81-85002-01 March 2004 B-5 131
- B-6 March 2004 81-85002-01 132
- 81-85002-01 March 2004 B-7 133
- B.4 Loading a Data Cartridge 134
- 81-85002-01 March 2004 B-9 135
- B-10 March 2004 81-85002-01 136
- Glossary 137
- G-2 March 2004 81-85002-01 138
- 81-85002-01 March 2004 G-3 139
- G-4 March 2004 81-85002-01 140
- 81-85002-01 March 2004 G-5 141
- G-6 March 2004 81-85002-01 142
- 81-85002-01 March 2004 G-7 143
- G-8 March 2004 81-85002-01 144
- 81-85002-01 March 2004 G-9 145
- G-10 March 2004 81-85002-01 146
- 81-85002-01 March 2004 G-11 147
- G-12 March 2004 81-85002-01 148
- 81-85002-01 A04 150
Relacionado con productos y manuales para Las unidades de cinta Quantum SDLT 320
Las unidades de cinta Quantum L500 Guía de usuario
(120 paginas)
(120 paginas)
Las unidades de cinta Quantum DLT4500 Manual de usuario
(360 paginas)
(360 paginas)
Las unidades de cinta Quantum DLT-V4 Manual
(28 paginas)
(28 paginas)
Las unidades de cinta Quantum DLT 7 Manual
(177 paginas)
(177 paginas)
Las unidades de cinta Quantum DLT 8000 Manual
(408 paginas)
(408 paginas)
Las unidades de cinta Quantum LTO-6 Guía de usuario
(38 paginas)
(38 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales