Quantum 1200 Series DAT Autochanger Guía de usuario Pagina 123
- Pagina / 294
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SDLT 600 SCSI Interface Guide Chapter 4: SCSI Commands
81-81200-02 REV A01 January 2005 4-81
TST Task Set Type. The drive maintains a single task set for all initiators. Must be set
to 0.
D_Sense Descriptor Format Sense Data. Not supported. Must be set to 0.
GLTSD Global Logging Target Save Disable. Must be set to 0.
RLEC Report Log Exception Condition. When set to 1, specifies that the drive reports
log exception conditions. When set to 0, specifies that the drive does not report log
exception conditions.
The RLEC bit works with the Read / Write Error LOG SENSE page, specifically,
the TMC bit of the Read / Write Error LOG SENSE page (page 02h and 03h),
described in Table 4-24 on page 4-44.
RLEC indicates whether the drive should return CHECK CONDITION status
with Sense Key set to UNIT ATTENTION when one of the READ and WRITE
error counters of the log pages reach a specified threshold. Modify the thresholds
using the LOG SELECT command.
Queue Algorithm
Modifier
Must be set to 0.
QErr Queue Error. Must be set to 0.
DQue Disable Queuing. Must be set to 0.
TAS Task Aborted Status. Must be set to 0, indicating that tasks aborted by other
initiators do not return a status.
RAC Report a Check. Must be set to 0, indicating that the drive may return BUSY
status.
UA_Intlck_Ctrl Unit Attention Interlocks Control. Must be set to 0, indicating that the drive clears
UNIT ATTENTION conditions when they are reported.
SWP Software Write Protect. Not supported. Must be set to 0.
Autoload Mode Indicates the action the drive is to take when tape medium is loaded. All values
not listed below are reserved.
Value Description
000b The medium is loaded for full access.
001b The medium is loaded for Enhanced Medium Auxiliary
Memory (EMAM) access only.
010b The medium is not loaded.
Table 4-49. Control Mode MODE SELECT Page — Field Descriptions (Continued)
Field Name Description
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Relacionado con productos y manuales para Software Quantum 1200 Series DAT Autochanger
Software Quantum SuperLoader 3 Guía de usuario
(160 paginas)
(160 paginas)
Software Quantum SuperLoader Guía de usuario
(196 paginas)
(196 paginas)
Software Quantum Scalar i2000 Guía de usuario
(544 paginas)
(544 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales