Quantum 1200 Series DAT Autochanger Guía de usuario Pagina 217
- Pagina / 294
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SDLT 600 SCSI Interface Guide Chapter 4: SCSI Commands
81-81200-02 REV A01 January 2005 4-175
Standard Medium Type Attributes
Medium type attributes (see Table 4-102) are hard-coded into the medium auxiliary memory at the
time of manufacture. All supported medium type attributes have a status of read only.
MEDIUM MANUFACTURER: Contains 8 bytes of ASCII data (see “Attribute Format” on
page 4-163) identifying the vendor of the media.
Total
Change
Partition
Count
Indicates the number of times that switches to the partition specified by the
Partition Number field in the CDB have been performed on the medium. Must be
set to 0. Super DLTtape media comprises a single volume.
Total
Partition
Initialize
Count
Indicates the number of times that the partition specified by the Partition Number
field in the CDB has been initialized. This count accumulates over the life of the
medium but it is reset to 0 after a medium format.
Table 4-102. Medium Type Attributes (for EMAM) Supported by the SDLT Tape Drive Firmware
Attribute
Identifier
Name
Attribute
Length
Format Details
0400h MEDIUM MANUFACTURER 8 ASCII Page 4-175
0401h MEDIUM SERIAL NUMBER 32 ASCII Page 4-176
0402h MEDIUM LENGTH 4 BINARY Page 4-176
0403h MEDIUM WIDTH 4 BINARY Page 4-176
0404h ASSIGNING ORGANIZATION 8 ASCII Page 4-176
0405h MEDIUM DENSITY CODE 1 BINARY Page 4-176
0406h MEDIUM MANUFACTURE
DATE
8ASCIIPage 4-176
0407h MAM CAPACITY 8 BINARY Page 4-176
0408h MEDIUM TYPE (and MEDIUM
TYPE INFORMATION)
1 BINARY Page 4-176
0409h MEDIUM TYPE INFOMATION 2 BINARY Page 4-176
040Ah -
07FFh
Reserved
Table 4-101. PARTITION USAGE HISTORY Attribute Parameter Data —
Field Descriptions (Continued)
Field
Name
Description
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Relacionado con productos y manuales para Software Quantum 1200 Series DAT Autochanger
Software Quantum SuperLoader 3 Guía de usuario
(160 paginas)
(160 paginas)
Software Quantum SuperLoader Guía de usuario
(196 paginas)
(196 paginas)
Software Quantum Scalar i2000 Guía de usuario
(544 paginas)
(544 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales