Quantum 1200 Series DAT Autochanger Guía de usuario Pagina 208
- Pagina / 294
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
READ ATTRIBUTE Command (8Ch) SDLT 600 SCSI Interface Guide
4-166 January 2005 81-81200-02 REV A01
REMAINING CAPACITY IN PARTITION AND
MAXIMUM CAPACITY IN PARTITION: These are native capacities, assuming no data
compression for the specified medium partition, expressed in increments of 1,048,576 bytes; that is, a
value of 1 means 1,048,576 bytes, 2 means 2,097,152 bytes, and so on.
TAPE ALERT FLAGS: Provides a means of reporting the state of the Tape Alert flags for the
previous load of the medium. Each Tape Alert flag occupies 1 bit (Flag 1 = MSB, byte 1; Flag 64 =
LSB, byte 8). The bits specify all the Tape Alert flags set during the previous load — the bits are
“sticky” for the load.
0007h INITIALIZATION COUNT 2 BINARY Page 4-167
0008h - 020Ah Reserved
020Ah DEVICE VENDOR/SERIAL
NUMBER AT LAST LOAD
40 ASCII Page 4-167
020Bh DEVICE VENDOR/SERIAL
NUMBER AT LOAD-1
40 ASCII Page 4-167
020Ch DEVICE VENDOR/SERIAL
NUMBER AT LOAD-2
40 ASCII Page 4-167
020Dh DEVICE VENDOR/SERIAL
NUMBER AT LOAD-3
40 ASCII Page 4-167
020Eh - 021Fh Reserved
0220h TOTAL MBYTES WRITTEN IN
MEDIUM LIFE
8BINARYPage 4-168
0221h TOTAL MBYTES READ IN
MEDIUM LIFE
8BINARYPage 4-168
0222h TOTAL MBYTES WRITTEN IN
CURRENT/LAST LOAD
8BINARYPage 4-168
0223h TOTAL MBYTES READ IN
CURRENT/LAST LOAD
8BINARYPage 4-168
0224h - 033Fh Reserved
0340h MEDIUM USAGE HISTORY 90 BINARY Page 4-168
0341h PARTITION USAGE HISTORY 60 BINARY Page 4-172
0342h - 03FFh Reserved
Table 4-98. Device Type Attributes (for EMAM) Supported by the SDLT Tape Drive
Firmware (Continued)
Attribute
Identifier
Name
Attribute
Length
Format Details
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Relacionado con productos y manuales para Software Quantum 1200 Series DAT Autochanger
Software Quantum SuperLoader 3 Guía de usuario
(160 paginas)
(160 paginas)
Software Quantum SuperLoader Guía de usuario
(196 paginas)
(196 paginas)
Software Quantum Scalar i2000 Guía de usuario
(544 paginas)
(544 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales