Quantum LTO 2U Instrucciones de operaciones Pagina 53
- Pagina / 264
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
JULY 2007 MAGNUM 224, MAGNUM 448, STORAGELIBRARY T24, OR STORAGELOADER 2U
4-3
COMMAND STATUS
A request is made to scan a cartridge in a storage location and the operation
failed because the bar code scanner was unable to read the label on the
cartridge or if the cartridge does not have a label. The scan will not fail if the
location is empty. See Ta b l e 4 - 2 for details about how the cartridge inventory
is updated.
4.4 COMMAND STATUS
The library returns a status byte after processing the INITIALIZE ELEMENT
STATUS command as follows:
Good
The library returns Good status when it is able to process the command
without errors.
Busy
Busy status indicates that the library is temporarily unable to accept a
command from this initiator. The initiator may retry the command later.
Reservation Conflict
The library returns Reservation Conflict status when it is reserved by a
different initiator. See Chapter 20 for more information about the RESERVE
command.
Check Condition
Check Condition status is returned for the following reasons:
A Unit Attention condition is pending for the initiator.
The library has experienced an unrecoverable hardware error.
The library encounters a problem while scanning the cartridges.
The library is not ready because a magazine is removed.
Table 4-2 Effect on the cartridge inventory when a request for a cartridge scan fails
This cartridge inventory field...
...is changed to the following when the library cannot read the
cartridge label
Occupied 1
Occupied Valid 1
Label blanks
Label Valid 0
Label Scan Retries updated if retried
Source Storage Element Address no change
- EFERENCE 1014826 2
- ONTACTING 3
- ANDBERG DATA 3
- ORPORATION 3
- Contents 5
- SCSI REFERENCE 1014826 10
- ABOUT THIS MANUAL 17
- PRODUCT OVERVIEW 19
- 1.1.2 BACK PANEL COMPONENTS 20
- AGNUM 448 EMULATION MODES 24
- OVERVIEW OF THE LIBRARY 25
- SCSI DEVICE 25
- 2.1.1 ELEMENT TYPES 27
- 2.1.2 ELEMENT ADDRESSES 27
- Magnum 448 Element Addresses 29
- ELATIONSHIP TO THE SCSI BUS 31
- 2.2 SCSI COMMAND PROTOCOL 32
- OMMAND PROTOCOL 33
- 2.2.2 SCSI COMMAND FORMAT 34
- 2.2.3 COMMAND STATUS 35
- 2.2.4 COMMAND FORMAT ERRORS 36
- IMPLEMENTING SCSI 39
- OPERATIONS 39
- Disabling Sequential Mode 41
- Setting the Restart Option 41
- Setting the Loop Option 42
- Important 42
- ETTING ELEMENT ADDRESSES 43
- Element Addresses 45
- Element Occupied Status 46
- Bar Code Label Information 47
- 3.5 MOVING CARTRIDGES 48
- 3.7 PERFORMING DIAGNOSTICS 49
- Home Screen 50
- INITIALIZE ELEMENT 51
- STATUS (07h) 51
- 4.4 COMMAND STATUS 53
- STATUS WITH RANGE (37h) 55
- 5.4 COMMAND STATUS 58
- INQUIRY (12h) 59
- 6.3 WHAT THE LIBRARY RETURNS 60
- TANDARD INQUIRY DATA PAGE 61
- CODE 00h) 66
- Page Code – Byte 01 68
- Page Length – Byte 03 68
- 6.4 COMMAND STATUS 73
- LOG SELECT (4Ch) 75
- 7.3 COMMAND STATUS 76
- LOG SENSE (4Dh) 77
- 8.3 WHAT THE LIBRARY RETURNS 81
- 8.3.1 LOG PARAMETER FORMAT 82
- Parameter Length – Byte 03 83
- Parameter Value – Byte 04 90
- Command – Byte 04 91
- Fault Symptom Code – Byte 05 92
- Command Interface – Byte 06 93
- 8.4 COMMAND STATUS 94
- CHAPTER 8—LOG SENSE (4Dh) 96
- MODE SELECT (15h) 97
- 9.2.1 PARAMETER LIST HEADER 99
- Assigning Element Addresses 100
- ! Important 101
- HAT YOU SEND TO THE LIBRARY 103
- Page Length – Byte 01 104
- MaxStor – Byte 4, Bit 7 105
- Parameter Length – Byte 01 108
- Write Line 1 – Byte 02, Bit 3 108
- FixEnbl – Byte 02, Bit 0 109
- Auto – Byte 02, Bit 1 109
- 9.3 COMMAND STATUS 110
- MODE SENSE (1Ah) 113
- 10.3 WHAT THE LIBRARY RETURNS 115
- Mode Data Length – Byte 00 116
- HAT THE LIBRARY RETURNS 117
- CODE 1Eh) 119
- 10.4 COMMAND STATUS 130
- Check Condition 131
- CHAPTER 10—MODE SENSE (1Ah) 132
- MOVE MEDIUM (A5h) 133
- 11.4 COMMAND STATUS 137
- POSITION TO ELEMENT 139
- 12.3 COMMAND STATUS 140
- OMMAND STATUS 141
- PREVENT/ALLOW MEDIUM 143
- REMOVAL (1Eh) 143
- 13.3 COMMAND STATUS 144
- READ BUFFER (3Ch) 145
- 14.5 COMMAND STATUS 148
- CHAPTER 14—READ BUFFER (3Ch) 150
- READ ELEMENT STATUS 151
- 15.3 WHAT THE LIBRARY RETURNS 153
- 15.3.1 ELEMENT STATUS HEADER 154
- 15.3.2 ELEMENT STATUS PAGE 154
- Element Type Code – Byte 00 155
- PVolTag – Byte 01, Bit 7 155
- AVolTag – Byte 01, Bit 6 155
- 15.3.3 ELEMENT DESCRIPTORS 156
- Except – Byte 02, Bit 2 157
- TORAGE ELEMENT DESCRIPTOR 159
- Access – Byte 02, Bit 3 160
- Full – Byte 02, Bit 0 160
- SValid – Byte 09, Bit 7 161
- Invert – Byte 09, Bit 6 161
- 15.4 COMMAND STATUS 170
- RECEIVE DIAGNOSTIC 171
- RESULTS (1Ch) 171
- 16.3 WHAT THE LIBRARY RETURNS 172
- Bytes 02 and 03 – Page Length 173
- Page Code – Byte 00 173
- Page Length – Bytes 02 and 03 173
- Supported Log Pages – Byte 04 173
- Self Test – Byte 27 174
- 16.4 COMMAND STATUS 175
- RELEASE (17h OR 57h) 177
- 17.1 ABOUT THIS COMMAND 178
- 17.3 COMMAND STATUS 179
- REQUEST SENSE (03h) 181
- 18.3 WHAT THE LIBRARY RETURNS 183
- 18.4 COMMAND STATUS 186
- REQUEST VOLUME 187
- ELEMENT ADDRESS (B5h) 187
- 19.1 ABOUT THIS COMMAND 188
- 19.3 WHAT THE LIBRARY RETURNS 190
- 19.3.2 ELEMENT STATUS PAGE 191
- 19.3.3 ELEMENT DESCRIPTORS 192
- 19.4 COMMAND STATUS 204
- Reservation Conflict 205
- RESERVE (16h OR 56h) 207
- 20.1 ABOUT THIS COMMAND 208
- 20.3 COMMAND STATUS 209
- REZERO UNIT (01h) 211
- SEND DIAGNOSTIC (1Dh) 213
- DDITIONAL DIAGNOSTIC DATA 215
- ELF TEST PAGE (PAGE CODE F0h) 216
- 22.4 COMMAND STATUS 217
- SEND VOLUME TAG (B6h) 219
- ARAMETER LIST 221
- 23.4 COMMAND STATUS 222
- TEST UNIT READY (00h) 225
- WRITE BUFFER (3Bh) 227
- 25.4 COMMAND STATUS 230
- CHAPTER 25—WRITE BUFFER (3Bh) 232
- ERROR CODES 233
- IBRARY “FATAL” ERROR MESSAGES 243
- A.3 ERROR RECOVERY PROCEDURES 258
Relacionado con productos y manuales para Cintas De Datos En Blanco Quantum LTO 2U
(82 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales